Advancements in satellite technologies are increasing the power density of electronics and payloads. When the power consumption increases within a limited volume, waste heat generation also increases and this necessitates a proper and efficient thermal management system. Mostly, micro and nanosatellites use passive thermal control methods because of the low cost, no additional power requirement, ease of implementation, and better thermal performance. Passive methods lack the ability to meet certain thermal requirements on larger and smaller satellite platforms. This work numerically studies the performance of some of the passive thermal control techniques such as thermal straps, surface coatings, multi-layer insulation (MLI), and radiators for a 6U small satellite configuration carrying a mid-wave infrared (MWIR) payload whose temperature needs to be cooled down to 100K. Infrared (IR) imagers require low temperature, and the level of cooling is entirely dependent on the infrared wavelengths. These instruments are used for various applications including Earth observations, defence, and imaging at IR wavelengths. To achieve these low temperatures on such instruments, a micro-cryocooler is considered in this study. Most of the higher heat dissipating elements in the satellite are mounted to a heat exchanger plate, which is thermally coupled to an external radiator using thermal straps and heat pipes. The effects of the radiator size, orbital inclinations, space environments, satellite attitude with respect to the sun, and surface coatings are discussed elaborately for a 6U satellite configuration.

Publication: applsci-12-02858.pdf

Source: Applied Sciences, 2022, 12(6), 2858

Author: Shanmugasundaram Selvadurai, Amal Chandran, David Valentini, and Bret Lamprecht

Year: 2022

Content Tags: mli, multi-layer insulation, surface elements, surface coating a mesh, radiator, phase change material, thermocouples, finite element, finite elements, convergence, material properties, properties, CCHP

SINDA/FLUINT (Ref 1-7) is the NASA-standard heat transfer and fluid flow analyzer for thermal control systems. Because of its general formulation, it is also used in other aerospace specialties such as environmental control (ECLSS) and liquid propulsion, and in terrestrial industries such as electronics packaging, refrigeration, power generation, and transportation industries.

SINDA/FLUINT is used to design and simulate thermal/fluid systems that can be represented in networks corresponding to finite difference, finite element, and/or lumped parameter equations. In addition to conduction, convection, and radiation heat transfer, the program can model steady or unsteady single- and two-phase flow networks.

C&R’s SinapsPlus® is a complete graphical user interface (preand postprocessor) and interactive model debugging environment for SINDA/FLUINT (Ref 8, 9). SinapsPlus also supports the C language in addition to the traditional choice of Fortran for concurrently executed user logic.

This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data.

Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled.

The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc.

Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sfpaper.pdf

Source: IECEC

Author: Brent A. Cullimore

Year: 1998

Content Tags: design optimization, model correlation, parameterize, parametric, two-phase flow, two-phase, optical properties, submodels, registers, expression editor, user logic, concurrent engineering, concurrent design, dynamic mode, dynamic SINDA, specific heat, solver, constraint, slip flow, Phenomena, capillary systems, mixtures, working fluids, nonequilibrium, vapor compression, uncertainty, uncertainty analysis

This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data.

Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled.

The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc.

Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sf981574.pdf

Source: ICES 1998

Author: Brent A. Cullimore

Year: 1998

Content Tags: design optimization, model correlation, parameterize, parametric, two-phase flow, two-phase, optical properties, submodels, registers, expression editor, user logic, concurrent engineering, concurrent design, dynamic mode, dynamic SINDA, specific heat, solver, constraint, slip flow, Phenomena, capillary systems, mixtures, working fluids, nonequilibrium, vapor compression, uncertainty, uncertainty analysis

Optimization and Automated Data Correlation in the NASA Standard Thermal/Fluid System Analyzer

SINDA/FLUINT (Ref 1-7) is the NASA-standard heat transfer and fluid flow analyzer for thermal control systems. Because of its general formulation, it is also used in other aerospace specialties such as environmental control (ECLSS) and liquid propulsion, and in terrestrial industries such as electronics packaging, refrigeration, power generation, and transportation industries. SINDA/FLUINT is used to design and simulate thermal/fluid systems that can be represented in networks corresponding to finite difference, finite element, and/or lumped parameter equations. In addition to conduction, convection, and radiation heat transfer, the program can model steady or unsteady single- and two-phase flow networks. CRTech's SinapsPlus® is a complete graphical user interface (preand postprocessor) and interactive model debugging environment for SINDA/FLUINT (Ref 8, 9). SinapsPlus also supports the C language in addition to the traditional choice of Fortran for concurrently executed user logic. This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data. Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled. The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc. Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sfpaper.pdf

Source: IECEC 1998

Author: Brent A. Cullimore

Year: 1998

Content Tags:

Publication: NewOsummary.pdf

Source: ASME

Author: Brent A. Cullimore

Year: 2001

Content Tags: model calibration, CFD, parametric, design optimization, design synthesis, Phenomena

The major influence on the reliability of electronics is temperature, yet thermal/fluid modeling is plagued with uncertainties and unknowns. Nonetheless, if appropriate values of these unknown parameters are available for any specific electronics package, then its temperature response can be accurately predicted using modern thermal/fluid analysis tools.

Traditionally, uncertainties are dealt with by a combination of testing, safety factors or margins, and worst-case design scenarios. Analyses are performed iteratively in a repetitive “point design evaluation” mode. Computer-based design simulation tools have emphasized increasing detail and fidelity to physical phenomena, seemingly ignoring the fact that the inputs to these simulations are highly uncertain.

This paper describes both current and future methods of dealing with uncertainties in thermal engineering. It introduces advanced tools and alternative methodologies that can automate not only the quantification of reliability, but can also help synthesize designs on the basis of reliability. It advocates using rapid gains in computer speed not to increase the degree of detail in a model, but to help the engineer find a robust design by automating high-level design tasks.

Publication: IPACK2001-15516.pdf

Source: InterPack

Author: Brent A. Cullimore

Year: 2001

Content Tags: parameterize, parametric, contact conductance, design synthesis, Phenomena, robust design, design optimization, design variables, reliability engineering

Nonlinear Programming Applied to Calibrating Thermal and Fluid Models to Test Data (Semi-Therm 2002)

Publication: calibrating.pdf

Source: Semi-Therm

Author: Jane Baumann, Brent Cullimore

Year: 2002

Content Tags: model calibration, model correlation, condenser, condensers, validation, design optimization, parametric

This paper describes readily available techniques for automating the search for worst-case (e.g., “hot case”, “cold case”) design scenarios using only modest computational resources. These methods not only streamline a repetitive yet crucial task, they usually produce better results.

The problems with prior approaches are summarized, then the improvements are demonstrated via a simplified example that is analyzed using various approaches. Finally, areas for further automation are outlined, including attacking the entire design problem at a higher-level.

Publication: WorstCase-ICES.pdf

Source: ICES

Author: B. Cullimore

Year: 2003

Content Tags: parametric, model correlation, design optimization, convergence

A cryogenic capillary pumped loop (CPL) has been developed, designed, fabricated and successfully demonstrated by test. Using no moving parts, the novel device is able to start from a supercritical state and cool a remote dissipation source to 80-90K. Design studies were conducted for integration requirements and component design optimization and prototype units were designed, fabricated and successfully tested with excellent results. The development included the miniaturization of CPL technology to allow heat acquisition from sources with a small footprint and direct integration to a cryocooler cold finger. Applications include the cooling of cryogenic electronics, sensors, and fuels. The technology possesses many advantages over cryogenic heat pipes including ground testability and mechanical isolation. Because of the CPLs ability to transport loads over a distance, cryocoolers can be located remotely from the detector (up to a meter away or across a gimbaled joint). In addition, it passively seeks the coldest rejection environment, allowing a single cryogenic CPL to enable switching between multiple passive cryogenic radiators. This work was performed under funding from NASA Goddard Space Flight Center.

Publication: IECEC98.pdf

Source: IECEC

Author: Jane Baumann, Brent Cullimore

Year: 1998

Content Tags: capillary pumped loop, CPL, CCPL, cryogenic, cooling loop, supercritical, start-up, design optimization, two-phase, heat loads, working fluids, evaporator, condenser, robust design, capillary systems, wicks, heat pipe, heatpipe

Active cooling technologies such as heat pipes, loop heat pipes (LHPs), thermosyphons, loop thermosyphons (LTSs), and pumped single- or two-phase coolant loops require specialized modeling treatment. However, these 1D ducted systems are largely overlooked in 3D thermal modeling tools. The increasing popularity of CFD and FEM models and generation of analysis data from 3D CAD data are strong trends in the thermal analysis community, but most software answering such demands has not provided linear modeling elements appropriate for the simulation of heat pipes and coolant loops.

This paper describes techniques whereby CAD line-drawing methods can be used to quickly generate 1D fluid models of heat pipes and coolant loops within a 3D thermal model. These arcs and lines can be attached intimately or via linear contact or saddle resistances to plates and other surfaces, whether those surfaces are modeled using thermal finite difference methods (FDM), or finite element methods (FEM), or combinations of both. The fluid lines can also be manifolded and customized as needed to represent complex heat exchangers and plumbing arrangements. Furthermore, the assumption of 1D flow can be combined with 2D/3D models of walls, including advanced methods of extruding a complex 2D cross-section along a curved or mitered centerline.

To demonstrate these concepts, several distinct examples are developed and discussed.

Publication: FloCAD3-ICES.pdf

Source: ICES

Author: B. Cullimore, D. A. Johnson

Year: 2003

Content Tags: finite difference, heat pipe, Loop Heat Pipe, finite element, structural mesh, duct, noncondensible gas, condenser, wall

Publication: aerospace2005heatpipes.pps

Source: Aerospace Thermal Control Workshop

Author: Brent Cullimore, Jane Baumann

Year: 2005

Content Tags: LHP, Loop Heat Pipe, radiation analysis groups, concurrent engineering, heat pipe, system-level modeling, noncondensable gas, VCHP, CCHP, wall, two-phase heat transfer, two-phase flow, condenser, condensers, evaporator, evaporators

The pressure of the cryogen within a Dewar determines the operating temperature since the cryogen is typically in a saturated state. Thus, the operating temperature of a Dewar is directly related to the ambient pressure external to the Dewar and the flow losses associated with venting cryogen. Given the low vapor pressures of some cryogens, such as solid hydrogen, the vent flow from Dewars used in space can enter the transitional and molecular flow regimes. In order to accurately predict the operating temperature within such Dewars, the analysis tool used to model the cryostat must account for free molecular and mixed flow losses as well as those for continuum flow.

As part of our analysis of Dewar designs for the James Webb Space Telescope Mid-Infrared Instrument (MIRI), we modified the continuum flow modeling capability of SINDA/FLUINT to accurately predict the pressure drop due to transitional and molecular flow in the MIRI Dewar vent line. This paper describes the modifications made to the flow loss computations within the analyzer and the testing conducted to verify these modifications.

Publication: Schweickart.pdf

Source: Topsfield Engineering Service, Inc.

Author: Russell B. Schweickart and Gary Mills

Year: 2005

Content Tags: pressure drop, capillary tube, nozzle, manifold, valve, slip flow

Publication: TFAWS-08-1009_presentation.pdf

Source: TFAWS Short Course

Author: Paul Schallhorn, D. Michael Campbell, Sukhdeep Chase, Jorge Piquero, Cindy Fortenberry, Xiaoyi Li, Lisa Grob

Year: 2008

Content Tags: CFD, two-phase, slosh, thermal stratification, diffusion, boundary layer, twinned tanks, boiling

Thermal analysis is typically performed using a point design approach, where a single model is analyzed one analysis case at a time. Changes to the system design are analyzed by updating the thermal radiation and conduction models by hand, which can become a bottleneck when attempting to adopt a concurrent engineering approach. This paper presents the parametric modeling features that have been added to Thermal DesktopTM to support concurrent engineering. The thermal model may now be characterized by a set of design variables that are easily modified to reflect system level design changes. Geometric features, optical and material properties, and orbital elements may all be specified using user-defined variables and expressions. Furthermore, these variables may be automatically modified by Thermal Desktop’s optimization capabilities in order to satisfy user-defined design goals, or for correlating thermal models to test data. By sharing the set of design variables among analysis models spanning multiple disciplines, further integrated analysis and design may be accomplished. The framework into which Thermal Desktop is embedded in order to support an integrated Thermal/Structural/Optical design, analysis, and optimization system is also presented.

Publication: 00ICES-266.pdf

Source: ICES

Author: Timothy D. Panczak, Brent A. Cullimore

Year: 2000

Content Tags: concurrent engineering, parametric, parameterize, register, registers, dynamic mode, dynamic SINDA, symbol manager, expression editor, expressions, design optimization, orbital heating, model correlation, solver, optical properties, heat pipes, symbol, variables, case set manager, properties, structural

Historically, thermal/fluid modeling began as a means of validating and sometimes correcting passively cooled designs that had been proposed by nonspecialists in heat transfer and fluid flow. As dissipation fluxes have risen, and as air cooling reaches the limits of its usefulness, involvement of thermal engineers is required earlier in the design process. Thermal engineers are now commonly responsible for sizing and selecting active cooling components such as fans and heat sinks, and increasingly single and two-phase coolant loops.

Meanwhile, heat transfer and fluid flow design analysis software has matured, growing both in ease of use and in phenomenological modeling prowess. Unfortunately, most software retains a focus on point-design simulations and needs to do a better job of helping thermal engineers not only evaluate designs, but also investigate alternatives and even automate the search for optimal designs.

This paper shows how readily available nonlinear programming (NLP) techniques can be successfully applied to automating design synthesis activities, allowing the thermal engineer to approach the problem from a higher level of automation. This paper briefly introduces NLP concepts, and then demonstrates their application both to a simplified fin (extended surface) as well as a more realistic case: a finned heat sink.

Publication: Optimizing.pdf

Source: ITherm

Author: Brent A. Cullimore

Year: 2002

Content Tags: design optimization, parametric, design synthesis, design variables, variables, sink temperature