Thermal Desktop has the capability of modeling free molecular heat transfer (FMHT), but limitations are observed when working with large models during transient operation. To overcome this limitation, a MatLab program was developed that processes the Thermal Desktop free molecular conductors. It sets up the logic and arrays for the Thermal Desktop GUI used by SINDA/FLUINT. The theory of free molecular heating is presented along with the process required to setup the conductors, arrays, logic and Fortran subroutines for FMHT modeling in Thermal Desktop.

Publication: TFAWS07-1013.pdf

Source: TFAWS

Author: Eric T. Malroy

Year: 2007

Content Tags: transient, third-party software, user-defined Fortran array, radiation analysis groups, surface elements, radiation, radiation calculations, case set manager, user-defined Fortran arrays (UDFAs), submodels, radks

Maintaining low temperature payloads through atmospheric reentry and ground recovery is becoming a larger focus in the space program as work in biology, cryogenic and other temperature dependent sciences becomes a higher goal on the International Space Station (ISS) and extraterrestrial surfaces. Paragon analyzes reentry system thermal control, particularly technology regarding small thermally controlled payloads anticipated for use in sample return from the International Space Station.

To minimize system mass and utilize the powerful insulative properties of a hard space vacuum the internal cavity of a small reentry vehicle can be left open. Thermally this causes concern during reentry, as even at very high altitudes there is enough pressure to cause a significant impact on insulation stratagems, such as MLI that rely on a high vacuum. At lower altitudes the vehicle is moving much slower, so the intense heat load of reentry is finished but soak-back from outer heated surfaces to the payload is a significant issue when air is present to facilitate heat transfer between layers. Initial assumptions that the cold temperatures of the upper atmosphere would cause a net cooling affect in the post-reentry times were overturned by a simple analysis set done in Thermal Desktop involving worst and best case scenarios as air starts to enter the vehicle. Additionally, CFD low pressure zones were shown to exist behind the vehicle where it is open to the atmosphere when the vehicle is travelling at extreme reentry speeds. These pressures are not so low however to prevent air from entering the vehicle. The impacts of this now apparent soak back, during the last phases of an atmospheric reentry were investigated leading to the conclusion that analyses of lower atmospheric portions of a reentry are critical to reentry studies and significantly changed the results.

An updated design is theorized using the knowledge gained from the preliminary studies called the Cryogenic Extended Duration and Reentry Thermal Control System (CEDR TCS) and the design is fully passive making it a low-complexity, zero-power system that does not necessitate the use of any consumables. The CEDR TCS uses a two-way pressure relief valve or “breather valve” that would allow the pressures inside and outside the vehicle to equilibrate once a great enough pressure differential is applied. This will allow air to leave while the unit is in space vacuum and prevent air from coming in until much later in the re-entry after much of the reentry heat has had a chance to convect to the upper atmosphere. Through further analysis CEDR is hoped to display a capability of near cryogenic temperatures through an atmospheric reentry and long durations on the ground.

Publication: TFAWS2011-AE-005.pdf

Source: TFAWS

Author: Erika T. Bannon, Jared Leidich, Alex Walker

Year: 2011

Content Tags: mli, multi-layer insulation, heat loads, design optimization, CFD, transient, insulation, model correlation, phase change material, PCM, radiation, sink temperature, heat flux, radks, radiation analysis group, material properties

SINDA/FLUINT (Ref 1-7) is the NASA-standard heat transfer and fluid flow analyzer for thermal control systems. Because of its general formulation, it is also used in other aerospace specialties such as environmental control (ECLSS) and liquid propulsion, and in terrestrial industries such as electronics packaging, refrigeration, power generation, and transportation industries.

SINDA/FLUINT is used to design and simulate thermal/fluid systems that can be represented in networks corresponding to finite difference, finite element, and/or lumped parameter equations. In addition to conduction, convection, and radiation heat transfer, the program can model steady or unsteady single- and two-phase flow networks.

C&R’s SinapsPlus® is a complete graphical user interface (preand postprocessor) and interactive model debugging environment for SINDA/FLUINT (Ref 8, 9). SinapsPlus also supports the C language in addition to the traditional choice of Fortran for concurrently executed user logic.

This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data.

Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled.

The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc.

Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sfpaper.pdf

Source: IECEC

Author: Brent A. Cullimore

Year: 1998

Content Tags: design optimization, model correlation, parameterize, parametric, two-phase flow, two-phase, optical properties, submodels, registers, expression editor, user logic, concurrent engineering, concurrent design, dynamic mode, dynamic SINDA, specific heat, solver, constraint, slip flow, Phenomena, capillary systems, mixtures, working fluids, nonequilibrium, vapor compression, uncertainty, uncertainty analysis

This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data.

Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled.

The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc.

Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sf981574.pdf

Source: ICES 1998

Author: Brent A. Cullimore

Year: 1998

Content Tags: design optimization, model correlation, parameterize, parametric, two-phase flow, two-phase, optical properties, submodels, registers, expression editor, user logic, concurrent engineering, concurrent design, dynamic mode, dynamic SINDA, specific heat, solver, constraint, slip flow, Phenomena, capillary systems, mixtures, working fluids, nonequilibrium, vapor compression, uncertainty, uncertainty analysis

Optimization and Automated Data Correlation in the NASA Standard Thermal/Fluid System Analyzer

SINDA/FLUINT (Ref 1-7) is the NASA-standard heat transfer and fluid flow analyzer for thermal control systems. Because of its general formulation, it is also used in other aerospace specialties such as environmental control (ECLSS) and liquid propulsion, and in terrestrial industries such as electronics packaging, refrigeration, power generation, and transportation industries. SINDA/FLUINT is used to design and simulate thermal/fluid systems that can be represented in networks corresponding to finite difference, finite element, and/or lumped parameter equations. In addition to conduction, convection, and radiation heat transfer, the program can model steady or unsteady single- and two-phase flow networks. CRTech's SinapsPlus® is a complete graphical user interface (preand postprocessor) and interactive model debugging environment for SINDA/FLUINT (Ref 8, 9). SinapsPlus also supports the C language in addition to the traditional choice of Fortran for concurrently executed user logic. This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data. Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled. The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc. Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sfpaper.pdf

Source: IECEC 1998

Author: Brent A. Cullimore

Year: 1998

Content Tags:

Nonlinear Programming Applied to Calibrating Thermal and Fluid Models to Test Data (Semi-Therm 2002)

Publication: calibrating.pdf

Source: Semi-Therm

Author: Jane Baumann, Brent Cullimore

Year: 2002

Content Tags: model calibration, model correlation, condenser, condensers, validation, design optimization, parametric

The loop heat pipe (LHP) is known to have a lower limit on input power. Below this limit the system may not start properly creating the potential for critical payload components to overheat. The LHP becomes especially susceptible to these low power start-up failures following diode operation, intentional shut-down of the device, or very cold conditions. These limits are affected by the presence of adverse tilt, mass on the evaporator, and noncondensible gas in the working fluid. Based on analytical modeling correlated to startup test data, this paper will describe the key parameters driving this low power limit and provide an overview of the methodology for predicting a “safe start” design envelope for a given system and loop design. The amount of incipient superheat was found to be key to the enveloping procedure. Superheat levels have been observed to vary significantly based on evaporator design and even from unit to unit of identical designs. Statistical studies of superheat levels and active measures for limiting superheat should be addressed by both the hardware vendors and the system integrators.

Publication: AIAA2000-2285.PDF

Source: AIAA Thermophysics

Author: Jane Baumann, Brent Cullimore, Jay Ambrose, Eva Buchan, Brois Yendler

Year: 2000

Content Tags: Loop Heat Pipe, LHP, noncondensable gas, start-up, evaporator, wicks, parametric, Phenomena, working fluid, model correlation, parameter, heat loads, compensation chamber, transient, capillary systems

Modeling to predict the condition of cryogenic propellants in an upper stage of a launch vehicle is necessary for mission planning and successful execution. Traditionally, this effort was performed using custom, in-house proprietary codes, limiting accessibility and application. Phenomena responsible for influencing the thermodynamic state of the propellant have been characterized as distinct events whose sequence defines a mission. These events include thermal stratification, passive thermal control roll (rotation), slosh, and engine firing. This paper demonstrates the use of an off the shelf, commercially available, thermal/fluid-network code to predict the thermodynamic state of propellant during the coast phase between engine firings, i.e. the first three of the above identified events. Results of this effort will also be presented.

Publication: AIAA-2006-50513.pdf

Source: AIAA

Author: P. Schallhorn, D. Michael Campbell, Sukhdeep Chase, Jorge Piquero, Cindy Fortenberry, Xiaoyi Li, Lisa Grob

Year: 2006

Content Tags: Optimization, parametric, radiation, radiation analysis groups, conduction, evaporation, CFD, convergence, structural, heat flux, thermal stratification, register, two-phase, slosh, wall, splash

Publication: TFAWS-08-1009_presentation.pdf

Source: TFAWS Short Course

Author: Paul Schallhorn, D. Michael Campbell, Sukhdeep Chase, Jorge Piquero, Cindy Fortenberry, Xiaoyi Li, Lisa Grob

Year: 2008

Content Tags: CFD, two-phase, slosh, thermal stratification, diffusion, boundary layer, twinned tanks, boiling

Thermal analysis is typically performed using a point design approach, where a single model is analyzed one analysis case at a time. Changes to the system design are analyzed by updating the thermal radiation and conduction models by hand, which can become a bottleneck when attempting to adopt a concurrent engineering approach. This paper presents the parametric modeling features that have been added to Thermal DesktopTM to support concurrent engineering. The thermal model may now be characterized by a set of design variables that are easily modified to reflect system level design changes. Geometric features, optical and material properties, and orbital elements may all be specified using user-defined variables and expressions. Furthermore, these variables may be automatically modified by Thermal Desktop’s optimization capabilities in order to satisfy user-defined design goals, or for correlating thermal models to test data. By sharing the set of design variables among analysis models spanning multiple disciplines, further integrated analysis and design may be accomplished. The framework into which Thermal Desktop is embedded in order to support an integrated Thermal/Structural/Optical design, analysis, and optimization system is also presented.

Publication: 00ICES-266.pdf

Source: ICES

Author: Timothy D. Panczak, Brent A. Cullimore

Year: 2000

Content Tags: concurrent engineering, parametric, parameterize, register, registers, dynamic mode, dynamic SINDA, symbol manager, expression editor, expressions, design optimization, orbital heating, model correlation, solver, optical properties, heat pipes, symbol, variables, case set manager, properties, structural