Thermal Desktop has the capability of modeling free molecular heat transfer (FMHT), but limitations are observed when working with large models during transient operation. To overcome this limitation, a MatLab program was developed that processes the Thermal Desktop free molecular conductors. It sets up the logic and arrays for the Thermal Desktop GUI used by SINDA/FLUINT. The theory of free molecular heating is presented along with the process required to setup the conductors, arrays, logic and Fortran subroutines for FMHT modeling in Thermal Desktop.

Publication: TFAWS07-1013.pdf

Source: TFAWS

Author: Eric T. Malroy

Year: 2007

Content Tags: transient, third-party software, user-defined Fortran array, radiation analysis groups, surface elements, radiation, radiation calculations, case set manager, user-defined Fortran arrays (UDFAs), submodels, radks

Complex products are best developed in a collaborative design environment where engineering data and CAD/CAE results can be shared across engineering discipline boundaries within a common software interface. A new software tool that allows Electro-Optical (EO) sensors to be developed in this manner has been used to conduct an integrated Structural/Thermal/Optical (STOP) analysis of a critical lens subassembly in a flight payload. This paper provides a description of the software environment and a summary of the technical results that were produced with it.

Publication: SPIE_August2009_Collaborative_Design_of_EO_Sensors_final.pdf

Source: The Aerospace Corporation

Author: Jason Geis, Jeff Lang, Leslie Peterson, Francisco Roybal, David Thomas

Year: 2009

Content Tags: concurrent engineering, concurrent design, third-party software, mesh, finite element, mashing, parametric, material properties, optical properties, boundary conditions, conductance, structural, thermocouples, transient

SINDA/FLUINT (Ref 1-7) is the NASA-standard heat transfer and fluid flow analyzer for thermal control systems. Because of its general formulation, it is also used in other aerospace specialties such as environmental control (ECLSS) and liquid propulsion, and in terrestrial industries such as electronics packaging, refrigeration, power generation, and transportation industries.

SINDA/FLUINT is used to design and simulate thermal/fluid systems that can be represented in networks corresponding to finite difference, finite element, and/or lumped parameter equations. In addition to conduction, convection, and radiation heat transfer, the program can model steady or unsteady single- and two-phase flow networks.

C&R’s SinapsPlus® is a complete graphical user interface (preand postprocessor) and interactive model debugging environment for SINDA/FLUINT (Ref 8, 9). SinapsPlus also supports the C language in addition to the traditional choice of Fortran for concurrently executed user logic.

This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data.

Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled.

The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc.

Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sfpaper.pdf

Source: IECEC

Author: Brent A. Cullimore

Year: 1998

Content Tags: design optimization, model correlation, parameterize, parametric, two-phase flow, two-phase, optical properties, submodels, registers, expression editor, user logic, concurrent engineering, concurrent design, dynamic mode, dynamic SINDA, specific heat, solver, constraint, slip flow, Phenomena, capillary systems, mixtures, working fluids, nonequilibrium, vapor compression, uncertainty, uncertainty analysis

This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data.

Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled.

The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc.

Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sf981574.pdf

Source: ICES 1998

Author: Brent A. Cullimore

Year: 1998

Content Tags: design optimization, model correlation, parameterize, parametric, two-phase flow, two-phase, optical properties, submodels, registers, expression editor, user logic, concurrent engineering, concurrent design, dynamic mode, dynamic SINDA, specific heat, solver, constraint, slip flow, Phenomena, capillary systems, mixtures, working fluids, nonequilibrium, vapor compression, uncertainty, uncertainty analysis

Optimization and Automated Data Correlation in the NASA Standard Thermal/Fluid System Analyzer

SINDA/FLUINT (Ref 1-7) is the NASA-standard heat transfer and fluid flow analyzer for thermal control systems. Because of its general formulation, it is also used in other aerospace specialties such as environmental control (ECLSS) and liquid propulsion, and in terrestrial industries such as electronics packaging, refrigeration, power generation, and transportation industries. SINDA/FLUINT is used to design and simulate thermal/fluid systems that can be represented in networks corresponding to finite difference, finite element, and/or lumped parameter equations. In addition to conduction, convection, and radiation heat transfer, the program can model steady or unsteady single- and two-phase flow networks. CRTech's SinapsPlus® is a complete graphical user interface (preand postprocessor) and interactive model debugging environment for SINDA/FLUINT (Ref 8, 9). SinapsPlus also supports the C language in addition to the traditional choice of Fortran for concurrently executed user logic. This paper describes revolutionary advances in SINDA/FLUINT, the NASA-standard heat transfer and fluid flow analyzer, changing it from a traditional point-design simulator into a tool that can help shape preliminary designs, rapidly perform parametrics and sensitivity studies, and even correlate modeling uncertainties using available test data. Innovations include the incorporation of a complete spreadsheet-like module that allows users to centralize and automate model changes, even while thermal/fluid solutions are in progress. This feature reduces training time by eliminating many archaic options, and encourages the performance of parametrics and other what-if analyses that help engineers develop an intuitive understanding of their designs and how they are modeled. The more revolutionary enhancement, though, is the complete integration of a nonlinear programming module that enables users to perform formal design optimization tasks such as weight minimization or performance maximization. The user can select any number of design variables and may apply any number of arbitrarily complex constraints to the optimization. This capability also can be used to find the best fit to available test data, automating a laborious but important task: the correlation of modeling uncertainties such as optical properties, contact conductances, as-built insulation performance, natural convection coefficients, etc. Finally, this paper presents an overview of related developments that, coupled with the optimization capabilities, further enhance the power of the whole package.

Publication: sfpaper.pdf

Source: IECEC 1998

Author: Brent A. Cullimore

Year: 1998

Content Tags:

Recent years have witnessed more improvement to the SINDA/FLUINT thermohydraulic analyzer than at any other time in its long history. These improvements have included not only expansions in analytic power, but also the additions of high-level modules that offer revolutions in thermal/ fluid engineering itself.

One such high-level module, “Reliability Engineering,” is described in this paper. Reliability Engineering means considering tolerances in design parameters, uncertainties in environments, uncertainties in application (e.g. usage scenarios), and variations in manufacturing as the stochastic phenomena that they are. Using this approach, the probability that a design will achieve its required performance (i.e., the reliability) is calculated, providing an assessment of risk or confidence in the design, and quantifying the amount of over- or under-design present.

The design to be evaluated for reliability will likely have been produced using traditional methods. Possibly, the design was generated using the Solver optimizer, another high-level module available in SINDA/FLUINT. Using design optimization, the user quantifies the goals that make one design better than another (mass, efficiency, etc.), and specifies the thresholds or requirements which render a given design viable or useless (exceeding a performance limit, etc.). SINDA/FLUINT then automatically searches for an optimal design.

Robust Design means factoring reliability into the development of the design itself: designing for a target reliability and thereby avoiding either costly over-design or dangerous under-design in the first place. Such an approach eliminates a deterministic stack-up of tolerances, worst-case scenarios, safety factors, and margins that have been the traditional approaches for treating uncertainties.

In any real system or product, heat transfer and fluid flow play a limited role: there are many other aspects to a successful design than the realm of thermal/fluids that is encompassed by SINDA/FLUINT. Therefore, this paper concludes with brief descriptions of methods for performing interdisciplinary design tasks.

Publication: releng1.pdf

Source: CRTech White Paper

Author: Brent A. Cullimore

Year: 2000

Content Tags: design optimization, reliability engineering, robust design, constraints, boundary conditions, concurrent design, concurrent engineering, batteries, flow control, orifices, radiator, registers, two-phase flow, solver, model correlation, dynamic SINDA, dynamic mode, variables, Monte Carlo, material properties, third-party software, uncertainty analysis, uncertainty

Publication: NewOsummary.pdf

Source: ASME

Author: Brent A. Cullimore

Year: 2001

Content Tags: model calibration, CFD, parametric, design optimization, design synthesis, Phenomena

The major influence on the reliability of electronics is temperature, yet thermal/fluid modeling is plagued with uncertainties and unknowns. Nonetheless, if appropriate values of these unknown parameters are available for any specific electronics package, then its temperature response can be accurately predicted using modern thermal/fluid analysis tools.

Traditionally, uncertainties are dealt with by a combination of testing, safety factors or margins, and worst-case design scenarios. Analyses are performed iteratively in a repetitive “point design evaluation” mode. Computer-based design simulation tools have emphasized increasing detail and fidelity to physical phenomena, seemingly ignoring the fact that the inputs to these simulations are highly uncertain.

This paper describes both current and future methods of dealing with uncertainties in thermal engineering. It introduces advanced tools and alternative methodologies that can automate not only the quantification of reliability, but can also help synthesize designs on the basis of reliability. It advocates using rapid gains in computer speed not to increase the degree of detail in a model, but to help the engineer find a robust design by automating high-level design tasks.

Publication: IPACK2001-15516.pdf

Source: InterPack

Author: Brent A. Cullimore

Year: 2001

Content Tags: parameterize, parametric, contact conductance, design synthesis, Phenomena, robust design, design optimization, design variables, reliability engineering

Nonlinear Programming Applied to Calibrating Thermal and Fluid Models to Test Data (Semi-Therm 2002)

Publication: calibrating.pdf

Source: Semi-Therm

Author: Jane Baumann, Brent Cullimore

Year: 2002

Content Tags: model calibration, model correlation, condenser, condensers, validation, design optimization, parametric

This paper describes readily available techniques for automating the search for worst-case (e.g., “hot case”, “cold case”) design scenarios using only modest computational resources. These methods not only streamline a repetitive yet crucial task, they usually produce better results.

The problems with prior approaches are summarized, then the improvements are demonstrated via a simplified example that is analyzed using various approaches. Finally, areas for further automation are outlined, including attacking the entire design problem at a higher-level.

Publication: WorstCase-ICES.pdf

Source: ICES

Author: B. Cullimore

Year: 2003

Content Tags: parametric, model correlation, design optimization, convergence

Thankfully, the age of stand-alone fixed-input simulation tools is fading away in favor of more flexible and integrated solutions. “Concurrent engineering” once meant automating data translations between monolithic codes, but sophisticated users have demanded more native integration and more automated tools for designing, and not just evaluating point designs. Improvements in both interprocess communications technology and numerical solutions have gone a long way towards meeting those demands.

This paper describes a small slice of a larger on-going effort to satisfy current and future demands for integrated multidisciplinary tools that can be highly customized by end-users or by third parties. Specifically, the ability to integrate fully featured thermal/fluid simulations into Microsoft’s Excel™ and other software is detailed. Users are now able not only to prepare custom user interfaces, they can use these codes as portals that allow integration activities at a larger scale. Previous enabling technologies are first described, then examples and repercussions of current capabilities are presented, and finally in-progress and future technologies are listed.

Publication: COMAPI-ICES.pdf

Source: ICES

Author: B. Cullimore, S. G. Ring, J. Baumann

Year: 2004

Content Tags: parametric, parameterize, dynamic mode, dynamic SINDA, third-party software

In recent years, loop heat pipe (LHP) technology has transitioned from a developmental technology to one that is flight ready. The LHP is considered to be more robust than capillary pumped loops (CPL) because the LHP does not require any preconditioning of the system prior to application of the heat load, nor does its performance become unstable in the presence of two-phase fluid in the core of the evaporator. However, both devices have a lower limit on input power: below a certain power, the system may not start properly. The LHP becomes especially susceptible to these low power start-ups following diode operation, intentional shut-down, or very cold conditions. These limits are affected by the presence of adverse tilt, mass on the evaporator, and noncondensible gas in the working fluid. Based on analytical modeling correlated to start-up test data, this paper will describe how the minimum power required to start the loop is increased due to the presence of mass, noncondensible gas, and adverse tilt. The end-product is a methodology for predicting a “safe start” design envelope for a given system and loop design.

Publication: 1999-01-.pdf

Source: ICES

Author: Jane Baumann, Brent Cullimore, Boris Yendler, Eva Buchan

Year: 1999

Content Tags: Loop Heat Pipe, LHP, noncondensable gas, start-up, heat loads, compensation chamber, condenser, condensers, evaporator, evaporators, thermoelectrics, two-phase, two-phase flow, transient, bayonet, heat transfer coefficient, model correlation

The loop heat pipe (LHP) is known to have a lower limit on input power. Below this limit the system may not start properly creating the potential for critical payload components to overheat. The LHP becomes especially susceptible to these low power start-up failures following diode operation, intentional shut-down of the device, or very cold conditions. These limits are affected by the presence of adverse tilt, mass on the evaporator, and noncondensible gas in the working fluid. Based on analytical modeling correlated to startup test data, this paper will describe the key parameters driving this low power limit and provide an overview of the methodology for predicting a “safe start” design envelope for a given system and loop design. The amount of incipient superheat was found to be key to the enveloping procedure. Superheat levels have been observed to vary significantly based on evaporator design and even from unit to unit of identical designs. Statistical studies of superheat levels and active measures for limiting superheat should be addressed by both the hardware vendors and the system integrators.

Publication: AIAA2000-2285.PDF

Source: AIAA Thermophysics

Author: Jane Baumann, Brent Cullimore, Jay Ambrose, Eva Buchan, Brois Yendler

Year: 2000

Content Tags: Loop Heat Pipe, LHP, noncondensable gas, start-up, evaporator, wicks, parametric, Phenomena, working fluid, model correlation, parameter, heat loads, compensation chamber, transient, capillary systems

The primary thermal management issue associated with Space Solar Power (SSP) is the need to acquire, transport and reject waste heat loads, on the order of 3.8 GW, from the transmitter to remote radiator locations. Previous conceptual studies have focused on transporting these loads to large remote radiators. These concepts assumed the ability to transport the heat either passively or mechanical over large transport distances of 100 meters or more.

A recent study, Innovative Deployable Radiators (IDR) for Space Solar Power, focused directly on the thermal control issues. This study has produced new concepts which break the system into small clusters of radiators which have more reasonable transport lengths of 1-2 meters. This study considers a system based on the klystron conversion technologies with a system architecture based on cluster radiators located near the waste heat source. The study evaluated various fluids for use between 50 and 500°C to determine their viability for use in LHPs. The evaluation considered fluid properties in addition to material compatibility with traditional LHP wick and containment materials.

The results of this study have provided new insight regarding the feasibility and limitations of LHPs for Space Solar Power applications. New technology development areas have been identified for both traditional LHPs and liquid metal LHPs.

Publication: AIAA2001-3078.pdf

Source: AIAA

Author: Jane Baumann, Suraj Rawal

Year: 2001

Content Tags: radiator, LHP, Loop Heat Pipe, capillary pumped loop, CPL, noncondensable gas, evaporator, evaporators, condenser, condensers, working fluids, pressure drops

This paper describes the need for dynamic (transient) simulation of automotive air conditioning systems, the reasons why such simulations are challenging, and the applicability of a general purpose off-the-shelf thermohydraulic analyzer to answer such challenges.

An overview of modeling methods for the basic components are presented, along with relevant approximations and their effect on speed and accuracy of the results.

Publication: vtms2001.pdf

Source: VTMS

Author: Brent A. Cullimore, Terry J. Hendricks

Year: 2001

Content Tags: compressor, evaporator, evaporators, condensers, slip flow, working fluids, registers, vapor compression, throttle, capillary tube, choked

Modeling lessons learned form Ford, Visteon, GM, Delpi, Danfoss, etc.

Publication: VCimaps.pps

Source: ITherm

Author: Brent Cullimore

Year: 2002

Content Tags: vapor compression, compressor, two-phase heat transfer, evaporator, condenser, parametric, slip flow, finite difference

LHPs and CPLs are increasingly accepted as thermal control solutions for spacecraft, and they are being investigated for various terrestrial applications as well. For a potential user of these technologies, modeling at the system level has been difficult, to say the least, and concurrent engineering methods were non-existent. New methods are now available to address these needs and concurrent CAD methods result in fast and accurate model generation. These same tools can be used for system level modeling of heat pipes, both fixed conductance with or without noncondensible gas or variable conductance.

Historically the thermal/hydraulic modeling of LHP has been approached with either oversimplified, design specific spreadsheets, or detailed thermal hydraulic models developed by the advanced user or LHP developer. To model these devices properly, and consequently gain confidence in the technology, the user needs to be able to model the LHP at the system level without becoming “caught up” in detail. This does not imply that the intricacies of two-phase flow and heat transfer within the evaporator core and secondary wicks of LHPs and CPLs aren’t important; but they should be left to the developers and the effects of these details can easily be enveloped through a series of steady state analyses. The potential user of the technology should focus on developing quasi-steady analyses to perform worst-case enveloping estimates, statistical treatment of the uncertainties, and post-test calibrations for use in extrapolation to untestable conditions.  In a nutshell: if they are going to fly them, they’re first going to have to analyze them, integrated into their own vehicle model.

This presentation will identify important LHP and CPL design parameters and how they should be modeled in addition to outlining the criteria for developing a system level model using new concurrent CAD-based methods.

Publication: LHPmodelGuide.pps

Source: Aerospace Thermal Control Workshop

Author: Jane Baumann

Year: 2003

Content Tags: LHP, Loop Heat Pipe, compensation chamber, evaporator, evaporators, condenser, condensers, iface, capillary systems

The National Renewable Energy Laboratory (NREL) and U.S. Department of Energy (DOE) are interested in developing more efficient vehicle air conditioning (A/C) systems to reduce fuel consumption in advanced vehicle designs. Vehicle A/C systems utilizing electrically-driven compressors are one possible system design approach to increasing A/C system performance over various drive cycle conditions. NREL’s transient A/C system model was used to perform multivariable design optimization of electrically-driven compressor A/C systems, in which five to seven system design variables were simultaneously optimized to maximize A/C system performance. Design optimization results demonstrate that significant improvements in system COP are possible, particularly system COP > 3, in a properly optimized system design with dynamically-controlled operation. System optimization analyses investigated dynamic A/C system design strategies employing dual-compressor-speeds in electrically-driven systems to evaluate their effects on system performance. A system optimization methodology was developed which can systematically quantify impacts on A/C system design and performance resulting from varying degrees of design influence being given to widely different design objectives. The technique is based upon formulating optimization objective functions from linear combinations of critical design performance parameters that characterize independent design goals. It was demonstrated here by giving varying degrees of design influence to maximizing system COP and maximizing evaporator cooling capacity over SC03 and US06 drive cycles.

Publication: C599-061.pdf

Source: NREL

Author: T. Hendricks

Year: 2003

Content Tags: design optimization, compressor, condenser, evaporator, expansion, system-level modeling, design variables

This paper describes a vehicle-level simulation model for climate control and powertrain cooling developed and currently utilized at GM. The tool was developed in response to GM's need to speed vehicle development for HVAC and powertrain cooling to meet world-class program execution timing (18 to 24 month vehicle development cycles). At the same time the simulation tool had to complement GM's strategy to move additional engineering responsibility to its HVAC suppliers. This simulation tool called "e-Thermal" was quickly developed and currently is in widespread (global) use across GM. This paper describes GM's objectives and requirements for developing e-Thermal. The structure of the tool and the capabilities of the simulation tool modules (refrigeration, front end airflow, passenger compartment, engine, transmission, Interior air handling …) is introduced. Model data requirements and GM's strategy for acquiring component data are also described. The paper includes an example of a typical application of the tool with sample output from the simulation and some comparison to actual test data from a vehicle under the same test scenario.

Publication: 2004-01-1510.pdf

Source: SAE Technical Paper Series

Author: Todd M. Tumas, Balaji Maniam, Milind Mahajan, Gaurav Anand, Nagendra Jain

Year: 2004

Content Tags: Components, heat exchangers, system-level modeling, third-party software, refrigeration cycles, model correlation

e-Thermal is a vehicle level thermal analysis tool developed by General Motors to simulate the transient performance of the entire vehicle HVAC and Powertrain cooling system. It is currently in widespread (global) use across GM. This paper discusses the details of the airconditioning module of e-Thermal. Most of the literature available on transient modeling of the air conditioning systems is based on finite difference approach that require large simulation times. This has been overcome by appropriately modeling the components using Sinda/Fluint. The basic components of automotive air conditioning system, evaporator, condenser, compressor and expansion valve, are parametrically modeled in Sinda/Fluint. For each component, physical characteristics and performance data is collected in form of component data standards. This performance data is used to curve fit parameters that then reproduce the component performance. These components are then integrated together to form various A/C system configurations including orifice tube systems, txv systems and dual evaporator systems. The A/C subsystem uses airflow rates, temperatures, humidity’s and compressor speed as inputs. The outputs include overall system energy balance, system COP, refrigerant flow rates and system pressures. The A/C simulation runs about three times faster to three times slower than real time. The modeling technique used is also capable of tracking the effect of system charge on the overall system performance. A database of automotive air conditioning components accompanies the simulation tool. This database is then integrated in e-Thermal to provide the component data for modeling. Validation results for component level models are demonstrated. They form the basis of system level models. System level validation is also demonstrated. The simulation times vary from 3 times faster than real time to 5 times slower than real time depending on the nature of the simulation.

Publication: 2004-01-1509.pdf

Source: SAE Technical Paper Series

Author: Gaurav Anand, Milind Mahajan, Nagendra Jain, Balaji Maniam, Todd M. Tumas

Year: 2004

Content Tags: parametric, two-phase flow, two-phase, Components, heat exchangers, compressor, condenser, evaporator, expansion, system-level modeling, third-party software, refrigeration cycles, model correlation

Publication: aerospace2005heatpipes.pps

Source: Aerospace Thermal Control Workshop

Author: Brent Cullimore, Jane Baumann

Year: 2005

Content Tags: LHP, Loop Heat Pipe, radiation analysis groups, concurrent engineering, heat pipe, system-level modeling, noncondensable gas, VCHP, CCHP, wall, two-phase heat transfer, two-phase flow, condenser, condensers, evaporator, evaporators

Structural and thermal engineers currently work independently of each other using unrelated tools, models, and methods. Without the ability to rapidly exchange design data and predicted performance, the achievement of the ideals of concurrent engineering is not possible.

Thermal codes have been unable to exploit the geometric information in structural models and the CAD design database, and do not facilitate transfer of temperature data to other discipline’s analysis models. This paper discusses the key features in Thermal Desktop for supporting integrated thermal/structural analysis. Approaches to thermal modeling in an integrated analysis environment are discussed along with Thermal Desktop's data mapping algorithm for exporting temperature data on to structural model grid points.

Publication: 99es-40.pdf

Source: ICES

Author: Tim Panczak, Mark J. Welch

Year: 1999

Content Tags: structural, finite elements, finite difference, structural mesh, temperature mapping, temperature map, concurrent engineering, concurrent design, radiation calculations, CAD geometry, postprocessing, orbit, orbital heating, radiation analysis groups, Monte Carlo, ray tracing, data mapper, solver

Thermal analysis is typically executed with multiple tools in a series of separate steps for performing radiation analysis, generating conduction and capacitance data, and for solving temperatures. This multitude of programs often leads to many user files that become unmanageable with their multitude, and the user often looses track as to which files go with which cases. In addition to combining the output from multiple programs, current processes often involve the user inputting various hand calculations into the math model to account for MLI/Insulation and contact conductance between entities. These calculations are not only tedious to make, but users often forget to update them when the geometry is changed.

Several new features of Thermal Desktop are designed to automate some of the tedious tasks that thermal engineers now practice. To start with, Thermal Desktop is a single program that does radiation analysis, generates conduction/capacitance data and automates the building of a SINDA/FLUINT model to solve for temperatures. Some of these new features of Thermal Desktop are Radiation Analysis Groups, Property Aliases, MLI/Insulation Objects, Contact Conductance Objects, Model Browser, and the Case Set Manager.

This paper describes the application and benefits of Thermal Desktop along with other unique features used to automate the thermal analysis process.

Publication: tDesktop99.pdf

Source: ICES

Author: Mark J. Welch, Tim Panczak

Year: 1999

Content Tags: radiation analysis groups, property, alias, multi-layer insulation, mli, insulation, contact conductance, model browser, case set manager

Thermal analysis is typically performed using a point design approach, where a single model is analyzed one analysis case at a time. Changes to the system design are analyzed by updating the thermal radiation and conduction models by hand, which can become a bottleneck when attempting to adopt a concurrent engineering approach. This paper presents the parametric modeling features that have been added to Thermal DesktopTM to support concurrent engineering. The thermal model may now be characterized by a set of design variables that are easily modified to reflect system level design changes. Geometric features, optical and material properties, and orbital elements may all be specified using user-defined variables and expressions. Furthermore, these variables may be automatically modified by Thermal Desktop’s optimization capabilities in order to satisfy user-defined design goals, or for correlating thermal models to test data. By sharing the set of design variables among analysis models spanning multiple disciplines, further integrated analysis and design may be accomplished. The framework into which Thermal Desktop is embedded in order to support an integrated Thermal/Structural/Optical design, analysis, and optimization system is also presented.

Publication: 00ICES-266.pdf

Source: ICES

Author: Timothy D. Panczak, Brent A. Cullimore

Year: 2000

Content Tags: concurrent engineering, parametric, parameterize, register, registers, dynamic mode, dynamic SINDA, symbol manager, expression editor, expressions, design optimization, orbital heating, model correlation, solver, optical properties, heat pipes, symbol, variables, case set manager, properties, structural

Historically, thermal/fluid modeling began as a means of validating and sometimes correcting passively cooled designs that had been proposed by nonspecialists in heat transfer and fluid flow. As dissipation fluxes have risen, and as air cooling reaches the limits of its usefulness, involvement of thermal engineers is required earlier in the design process. Thermal engineers are now commonly responsible for sizing and selecting active cooling components such as fans and heat sinks, and increasingly single and two-phase coolant loops.

Meanwhile, heat transfer and fluid flow design analysis software has matured, growing both in ease of use and in phenomenological modeling prowess. Unfortunately, most software retains a focus on point-design simulations and needs to do a better job of helping thermal engineers not only evaluate designs, but also investigate alternatives and even automate the search for optimal designs.

This paper shows how readily available nonlinear programming (NLP) techniques can be successfully applied to automating design synthesis activities, allowing the thermal engineer to approach the problem from a higher level of automation. This paper briefly introduces NLP concepts, and then demonstrates their application both to a simplified fin (extended surface) as well as a more realistic case: a finned heat sink.

Publication: Optimizing.pdf

Source: ITherm

Author: Brent A. Cullimore

Year: 2002

Content Tags: design optimization, parametric, design synthesis, design variables, variables, sink temperature

Publication: 17th_EWTES_MOLINA_FREQUENCYDOMAIN.pdf

Source: 17th Workshop on Thermal and ECLS Software-ESTEC

Author: Marco Molina, Christian Vettore

Year: 2003

Content Tags: third-party software, radks, heating rates

Thermal engineering has long been left out of the concurrent engineering environment dominated by CAD (computer aided design) and FEM (finite element method) software.  Current tools attempt to force the thermal design process into an environment primarily created to support structural analysis, which results in inappropriate thermal models. As a result, many thermal engineers either build models “by hand” or use geometric user interfaces that are separate from and have little useful connection, if any, to CAD and FEM systems.

This paper describes the development of a new thermal design environment called the Thermal Desktop. This system, while fully integrated into a neutral, low-cost CAD system, and which utilizes both FEM and FD methods, does not compromise the needs of the thermal engineer. Rather, the features needed for concurrent thermal analysis are specifically addressed by combining traditional parametric surface-based radiation and FD based conduction modeling with CAD and FEM methods. The use of flexible and familiar temperature solvers such as SINDA/FLUINT is retained.

Publication: ices-98es-51.pdf

Source: ASME

Author: Tim Panczak, Steve Ring, Mark Welch

Year: 1997

Content Tags: finite element, finite difference, concurrent engineering, heater, heatpipe, heat pipe, radiation analysis groups, optical properties, Phenomena, refraction, scaffolding, CAD geometry, layers, expression editor, solver, mesh, mesher, structural mesh, ray tracing, boundary conditions, thermal stress, radiator, conductance, batteries, orbital heating, mli, multi-layer insulation, radks, articulation, articulating